Level of Study
Place of Instruction
Objectives and Content
This course aims to provide an insight into the physics behind various energy technologies. It allows students to gain knowledge pertaining to practical energy conversion devices, their efficiency, their technology maturity along with their potential for improvement, and future technologies with their prospects; also a consideration of the sustainable use of materials in order to reduce the demand for energy in manufacturing.
During the semester students are expected to deepen their subject knowledge in: the extraction of fossil fuels (oil, natural gas and coal) along with their processing ready for subsequent use, the physics and chemistry of combustion including thermodynamic laws and energy concepts, the formation of pollutants, internal combustion engines (including steam turbines and heat engines) along with possibilities for heat recovery, the impact of pollutants on the environment, the conversion of light into electrical power and associated solar technologies, the design and aerodynamics of wind energy devices, nuclear and fusion reactor physics and aspects of proliferation and, the energy demands that the use of materials creates. A common theme is that the student will be given a comprehensive explanation of the physics pertaining to current devices and factors that affect their design, the state of current knowledge, and future predictions with possible implementations.
On completion of the course the student should be able to, defined in terms of knowledge, skills and general competence:
- understands and can describe the physics of various energy conversion processes
- can demonstrate an expanded knowledge on various topics and challenges related to all stages between the sourcing and the harnessing of various sources of energy; and
- shows a critical awareness of and be able to explain societal aspects of energy conversion including health and environmental issues
- critically understands the principals which govern the design of energy harnessing devices and, on a fundamental level, be able to offer design evaluations including a consideration of the embedded energy and energy required to manufacture a device
- make assessments through calculation of the energy available or produced from a system or device in various scenarios
- can communicate with engineers, technologists and scientists about the physics and design of energy conversion equipment in a critical and informed manner
Required Previous Knowledge
MAT111 Calculus 1 or equivalent
Recommended Previous Knowledge
Credit Reduction due to Course Overlap
ENERGI220: 5 ECTS
Access to the Course
Access to the course requires admission to a programme of study at The Faculty of Mathematics and Natural Sciences
Teaching and learning methods
The course will be delivered by subject specialists from academia and, where appropriate, from outside academia. Normally, the course will consist of a combination of lectures and tutorials as deemed appropriate by each subject specialist; but will typically consist of 1 x 2hour lecture and 1 x 2 hour tutorial each week. The exercises will normally include practice in calculations and discussions of topics addressed in the lectures; however, for broader topics there may be 2 x 2hours of lectures in a week with calculation interspersed within the lectures.
Compulsory Assignments and Attendance
There are no mandatory in-course assignments.
Forms of Assessment
Written formal closed book examination 4 hours. Typically, there will be a choice of questions in the examination.
Due to the measures taken to avoid the spread of SARS-CoV-2, UiB is closed for teaching and assessment. As a consequence, the following changes is made to assessment spring semester 2020:
- Written home examination instead of written examination
Examination Support Material
Non-programmable calculator, according to the faculty regulations.
The grading scale used is A to F. Grade A is the highest passing grade in the grading scale, grade F is a fail.
Examination both spring semester and autumn semester. In semesters without teaching the examination will be arranged at the beginning of the semester.
The reading list will be available within June 1st for the autumn semester and January 1st for the spring semester
The course will be evaluated by the students in accordance with the quality assurance system at UiB and the department
Normally, referents groups will be used each year.
The Programme Committee is responsible for the content, structure and quality of the study programme and courses.
For written exams, please note that the start time may change from 09:00 to 15:00 or vice versa until 14 days prior to the exam. Autumn 2020 written exams will be arranged either at home or on campus. Please see course information on MittUiB.
Type of assessment: Written examination
- 10.12.2020, 09:00
- 4 hours
- Withdrawal deadline
- Examination system
- Digital exam